Model B

That looks like quite the item! The whole website looks like it will be interesting to go through.

That's for sure Deb!

@youngNewbie, so happy you enjoyed your first experience with the Model B! I know when I took it out of the box the first time, my initial thought was "no way"! But there is a way and it is now one of my favorite nozzles.

Glad you had a good time with it!!

Deb

@youngNewbie, so happy you enjoyed your first experience with the Model B! I know when I took it out of the box the first time, my initial thought was "no way"! But there is a way and it is now one of my favorite nozzles.

Glad you had a good time with it!!

Deb

It's definitely a "lots of lube, slow in and out, take your time and breathe deep" nozzle, but it feels so good....

Well today was my third use of my model b. After two clean outs with warm water, I put coffee in my can, switched nozzles to the model b, lubed the head of it and my anus with coconut oil,and voila! All the way in! I opened up the clamp and soon it was all inside. I followed someone on here’s suggestion and just my body push the nozzle out on its own. Felt incredible. It was quite the clean out too! Love it!

I have changed the process to insert a model B. I used to use a lot of lube, but the down side was the nozzle wanted to come out during the enema, had to hold it in. New process, lube up anus and cheeks and the first half of the nozzle only. Begin to insert model B rotating and pushing to get the big bulb in. Then, push, pull, rotate the nozzle, push, clench, might take 10 minutes, until it seats fully in, what an unreal feeling!! I tend to pull it back and do the routine over again, it feels so good. With less lube, it tends to stay in place, almost a hands free situation. You can either play or start an enema, win-win in my opinion.

Like trw, the first few times I used my Model B, I also put too much lube on it and had it slide out. Once I started just lubing the first larger bulb and just behind, it goes in fine and stays in place much easier.

Dan

Like trw, the first few times I used my Model B, I also put too much lube on it and had it slide out. Once I started just lubing the first larger bulb and just behind, it goes in fine and stays in place much easier.

Dan

First time I put lube on the whole thing and it was very hard to get in. I rapidly found out that it was too floppy to hold at the end and push in, and the lube on the middle made it almost impossible to grab and push from the middle. I now do what Dan and TRW do so that the middle section is "grabbable". Lube the first bulge and your anus and everything works just fine.

As great as the Model B feels, not only while going in, it is nice to be able to enjoy it without worrying about it slipping out at the wrong time. Also, with less lube on it, inserting is much easier without it sliding around in the hand. Great for organic coffee.

Dan

To all who ordered your Model B - which softness did you select, and how do you like it? If you ordered again, would you order a different one, or keep the one you got?

To all who ordered your Model B - which softness did you select, and how do you like it? If you ordered again, would you order a different one, or keep the one you got?

I purchased mine in the #18 mildly firm softness for the translucent clear color. I would keep the same softness level. Unlike others, it tends to be one of my first nozzles if I'm taking a series of enemas (progression to the the DBLBL-3XL and maybe to the SNCMAX3). I like it because it allows a deep injection of the solution and the combination does a decent job of holding the solution in. It actually seals better if I don't press it all the way in. The egg-shaped ball seems to seat better with the top of my rectum than when inserting it that last inch to the retention flange.

But also is a great nozzle to rock back and forth on when fully inserted (I use L-shaped connectors to allow me to settle down on the nozzle and still allow for the enema solution to fill me) as the bending and slight movement in my rectum can be exceptionally stimulating.

Mine is #10 soft, and I like it. If you rush the insertion, the nozzle can fold over enough to not allow flow until you pull it out a little bit. After using the nozzle a couple of times (seated correctly), you know the feeling when it's "right", and it's a great feeling!!

I have the #10 and it works but I sure wouldn't get any softer. Feels good going in, and nice to squeeze around, but sometimes I wonder if the #18 would be a bit better. Hard to tell without trying one out. I think that either of the two would likely work, though.

I have the #10 and it works but I sure wouldn't get any softer. Feels good going in, and nice to squeeze around, but sometimes I wonder if the #18 would be a bit better. Hard to tell without trying one out. I think that either of the two would likely work, though.

I agree with @moliere 100%. My Model B is in the #10 softness and I love the way it compresses as it slides through my anal sphincter and bulges into full bloom in my rectum. That said, there have been times when getting it in has been a bit of a challenge (especially if I went nuts with lube) but overall, I love it!

Deb

This is great, thank you all for your replies!

To those who ordered recently, how long did it take for your order to arrive? The website says they are backlogged, so it would be great to find out from someone who used them recently.

Figure on 4 weeks, if lucky, 3 weeks.

To those who ordered recently, how long did it take for your order to arrive? The website says they are backlogged, so it would be great to find out from someone who used them recently.

I ordered a Model B on 15 October. A shipping confirmation came in on 19 December, 65 days later if I have counted correctly. Being in Australia, I don’t expect to receive the parcel until some time in January, and USPS tracking data has yet to indicate that it has left West Virginia :/

I was lucky - found one in stock and had it within a week! Wasn’t during the busy holidays though!

I order one in Oct and it toke 60 days to get it. Well worth the time it feels great inside. It does take some time to loose up the opening to insert it but once it's great. When time to remove it I just let my body push it out much better then trying to pull it out. I have my in right now and will leave it for a couple hours.

I ordered a Model B on 15 October. A shipping confirmation came in on 19 December, 65 days later if I have counted correctly. Being in Australia, I don’t expect to receive the parcel until some time in January, and USPS tracking data has yet to indicate that it has left West Virginia :/

USPS tracking doesn't work the same way as UPS/FedEx/DHL/whatever. You may only get a "ping" that they accepted it and a "ping" that it was delivered. You might get some midpoint pings too. I expect you'll get a notice as soon as they hand it off to Australia Post.

USPS tracking doesn't work the same way as UPS/FedEx/DHL/whatever. You may only get a "ping" that they accepted it and a "ping" that it was delivered. You might get some midpoint pings too. I expect you'll get a notice as soon as they hand it off to Australia Post.

I’ve had several pings, but for the last few days it’s been ‘between facilities’.

I hope it doesn't end up like this one:

https://images.app.goo.gl/NxXMa52ad9Xd8Pjs5