Starting to Explore - Need Ideas for DIY electrodes (Female)

First time experimenting with E-Stim. I picked up a TENS machine and it has a lot of potential. The problem is that the pads it comes with do not work well with the female anatomy. Perhaps I am missing an angle or location - feel free to give me tips on this as well. Think that the issue is not having the right type of electrode to work with. For now just using the large pads that came with the device.

Any suggestions specifically for the female anatomy? Specifically interested in the clit, but also open to suggestions for vagina and anal as well.

Try an anal/rectal monoploar fully insertable egg or butt plug electrode and an adhesive pad on your shaved clit/hood.

Start at zero and pick the power up SLOWLY. At first you won't feel much in the rectum but your clit will feel it first. As the power goes up,you will feel it both places.

You could probably make some inexepensive insertables by getting aluminum tape from the hardware store. This is the good stuff for sealing ducts. Not ducttape, not aluminized mylar. You can cut it to shape and stick it to an appropriate cylindrical object with ends available to connect the electrodes/wires. If you are anywhere near Montreal/Ottawa I would be happy to help. You could even DIY with aluminium foil and double sided sticky tape...

Just thought of this. Most cigar tubes are aluminium... great conductor.. you may have to sand the paint off with very fine sandpaper or steel wool...

On ebay you can buy all kinds of stuff. Anything aluminum or stainless. So any stainless speculum wold make a good vaginal electrode. You can often find stainless and aluminum enema nozzles. They would be good for anal or vaginal playing.

If you are the DIY type you could snip some aluminum out of a beverage can and make a pair of flats that would fit over the ridges on an alligator clip, so you could use the clip on your clit.

Still looking for more ideas - the unit I picked up has large pads (does not have alligator clips), and I have not had any luck attaching pads to metal items (i.e. spoons) to carry the current to different locations.

What connects the stim unit to the pads?

If you don't like the pads you can snip them off and than strip the wire and connect it to clips. If the unit uses a jack to output the power to the pads you could buy a make connector that matches the jack. That way the pads are still intact.

You could also buy an inline female connector and two male connectors and a set of clips and connect the output of the stiim unit to the inline jack, and wire the pads to one male connector and the clips to the other. That way you can quickly switch between them.

Snaps attach the leads to the pads. I will see if I can find another connector that matches the jack. I don't want to wreck the unit by hacking at the existing leads (at least not until these pads die).

Take a peek here efetish: http://www.happystim-usa.com/catalog/c14_p1.html

If you want to post a photo to your gallery of the cabling and your box connectors I can help you determine a suitable replacement cable arrangement. Thanks!

The best thing I have found for shocking clits is ti use a wooden clothes pin with a turn of thick copper wire wrapped around each side. Connect the wire from one side to the positive terminal of your device, and the wire from the other side to the negative terminal.

There are a few things to keep in mind doing it this way. Because the distance between the positive and negative contacts is so small, there will be less resistance between them than there is with most other configurations, so you will have to turn the juice way down. As usual, start at zero and slowly work you way up. Also, the clothes pin may grab with more force than is comfortable for a clitoris. There are a few ways to fix this. You can pull the clothes pin apart and bend the metal spring out a bit to decrease the closing force. This works but can be tough to do precisely enough and you can loosen the clip too much so that it does not stay on, or stay together well. You can also put a rubber band around the opposite end of the clothes pin (the part you pinch to open it). I suggest using a thick rubber band and cutting it, then tying a small loop of it around the pin, rather than wrapping a small band around it repeatedly, it is easier to adjust. Also, unless you put a stop in it somewhere, if the clothes pin closes with nothing in between the wires, it'll short out. This won't be a problem for the user, but it may damage whatever circuitry is powering it. Hold the clip open and put a bit of hot glue near the spring to prevent it from closing all the way. I also suggest wrapping any exposed wire that is outside of the clamping part with electrical tape so you don't take a jolt while handling it.

This sounds like a great idea but would completely hurt my wife. Her clit is very sensitive. Love he idea!

Okay.. what I found and it's really easy is this at current pleasures https://www.currentpleasures.com/collections/electrode-pads/products/silicone-circle-small-grey

You get two.. keep one as is. and cut one into a strip about and inch wide or less..

You will need to get some wires unless the pads you have have pins.

The large one goes over your clit.. your lips hold it in place.. genius lips.. lol.. the other goes into the vag.. deep.

You will feel this mostly right on the clit.. move that one until you find the spot..

You can also plug a small dildo into the other channel when you upgrade. it will slip past the trod already in the vag.

This is a really fun and a satisfying ride!!