What electrodes do you typically use?

I currently have a Nexus iStim unit, with which I use conductive rubber tubing. I use half inch lengths of acrylic tubing (half inch) as "collars" to tie the tubing in a loop for my mid-cock and for the head. Around the base of my cock, I use extra long sections of conductive tubing (like 11 inches to a foot) which I can tie very tightly. It helps get my cock good and hard as it acts like a cock ring. Tight rubber tubing at the base, loop of rubber (All conductive) and I'm ready to turn up trhe juice!

I have made one important mod to the iStim. I noticed that it used 9v batteries for power. This was fine, but the batteries would grow weak sometimes just as I was reaching "the reward". I have owned computers and accessiories for a coiuple of decades. This has left me, a confirmed packrat, with a good collection of left over plugin DC power supplies. I took the best 9v power supply I could find and soldered the plug to a couple of wires, the centre pin of the plug being the positive (+) and the outside rim the negative (-)I attached these wires with solder to the metal battery contacts, then used hot melt glue to keep the soldered wire/plug from moving around. I closed the sliding door and plugged in the whiole Frankensteined iStim unit to the nearest socket, wrappped my cock in conductive rubber tubing and CAREFULLY turned on the power. Holy cow!!! YOW! JESUS!!! batteries never felt ike this. It added a lot of power to the iStim unit and to my unit.

I'm using Smartstim on my PC, connected via a small stereo unit. Everything can be controlled ... even by someone on the other side of the globe! Awesome, hey!?

Irrespective, I've tried pretty much all placed to place the trodes ... and personally I don't like anal because in my mind it's too close to the prostate. Guys, we don't want to mess with it! So, I am back to basics and it gets me to HFO 99.5% of the time ... I don't even know how too use my hand ;-) What for, stimming is so much better!

I use conductive rubber. Reason is, you can make it fit perfectly and I've never experienced any burning sensation (except of course when someone turns the unit up way too high). Metal trodes can burn you (ok, maybe not you but me). So, I use one ring around base of cock and behind balls and a bipolar trode just behind the head. the sensation is amazing. And best is, it's all made DIY by myself. If you want to chat and/or play, you can find me oin yahoo messanger or skype:gh_txt001. If I don't answer immediately, it's because I'm on the road.

Suction cup electrodes used for EKG's are great. you can get em on Ebay. They are metal reusable electrodes that have a small rubber bulb to provide suction.They can be stuck almost anywhere.

Estim attachments I have are:

Sound

Cock rings

Conductive rubber loops

Anal prob

Inflatable anal probe

Vaginal probe

Various patches

Tad pole (my favourite one!)

Clit probe

And finally the pin wheel.

I would like to buy the strap on harness and cock next

The leads i have are the lil square sticky pads. They are easy enough to afix some how. Seems we always figure it out.

I have electrasim wwwelectrastim.co.uk

it has many varible controls and two patients hook up

I typically use a modified aneros MGX for some bi-polar prostate fun. The front side is wired up with 3 metal rings around my cock and balls for the common. I use a homemade head trode made of thick copper wire that wraps around the shaft just behind the glans with a loop that goes about an inch into the urethra. It feels really good.

I power it with a home built Davey box featured on Smarts time. I use the smarts time software and MP3s as my mood suits me. Lately, I have just been slapping on some TENS pads and using that because I've felt a bit lazy.

I'm cheap/poor. I've been at this for 50 years and I use silver solder, no lead, no rosin. You can shape it to wrap around your penis head and base and it's a great conductor with no penetrating residue to cause any problems. Works for me.

Metal disk electrodes made from drawer pulls. You can get them at home depot. chrome flat round knobs. You can mount them in a PVC pipe cap to insulate the user as they use it on the recipient. Also, EKG suction cup electrodes are very versitile. Use electrode gel or water based KY with these though.