I'm about to get rid of my double balloons

I have two double-balloon nozzles; one latex from medtech3000, the other silicone, I presume, from Amazon. Maybe I'm doing something wrong, but neither helps me retain the liquid; in fact, if I'm not very careful, the water comes out without any problems. For the umpteenth time, a few minutes ago, I tried the German one again, and it just doesn't work. I'll tear it into little pieces and throw it away tomorrow. In the next few days, I'll try the silicone one again, but I think it will have the same fate. Are you happy with it?

I’ll ask the obvious: Are you pumping up the balloons adequately and making sure you are keeping the screws turned completely clockwise after inflation in order to prevent deflation while in use?

Perhaps you are not inflating the balloons to a high enough capacity to properly retain the enema without leaks. Try inflating the balloons to become larger and see if that helps. Also make sure that your air pumps are not allowing the air to leak back out. Finally, if air leaking is a problem, try placing a clamp on the air hoses until time to release and deflate.

I've already done all the tests I could. Even the German latex one buckled because I over-inflated it. There are no air leaks, and it's all taped.

Is it possible that it's a problem with my body shape? Otherwise, it's inexplicable...

I’ve had similar issues with inflatable balloon also. I threw mine away because they were too uncomfortable and leaked more than other nozzles that used. The double balloon nozzles only work on persons with a normal anal canal length. Women tend to have a slightly shorter anal canal length than men. It can be from 3cm- 5.3 cm in length. If you have a long anal canal length, example 5.3 cm and there is 4 cm between the balloons when they are inflated the nozzle will not make a tight seal and you will leak a lot of water.

Try filling a sink full of water or a large bucket, pump them up and hold the whole unit under water to see if any air bubbles come out somewhere.

The only issue other than under inflating or air leaks (due to number of reasons) that could cause leaks is multiple really big, internal hemorrhoids that are located where inner balloon is supposed to reset against rectum wall creating the seal.

Chance is low, but I cannot think about about any other reason. But I would still put my money on operator errors.

I would suggest trying one of the inflatable butt plug style nozzles.

They are silicone and pretty darn cheap on amazon. The one I use is comfortable and seals me well. Here’s a link

https://www.amazon.com/Inflatable-Congestion-Cleaning-Expansion-Beginner/dp/B0CZRLPLQC/ref=sr_1_2?dib=eyJ2IjoiMSJ9.FF0G0ZHGooHatdjx2jr6WGMpCz3s0mDABIa6LRlE-nJ5wwoUKuVC3izTDzYsisSPup6eU0cQGXy0qGhfmHLS7chMnfMAJGjJSCNQl-EWjKnQpYahpNxqXDpLEnjNMObQd0oYdvpTZhyOsTjUil13aYcpCwNQE0wH3QWlfxOAixejT32ds6uJLCmU7MnKgG5kaw-YmOKpSczPjVD8oiYvdm2RQ0i81HfLq3GI03JHsIRyTACNByfA0E1X5frWNsIyKSmRzCicyusnruosSSxeseHWYG7bhaJ9HnUmE0jq6jw.BpcLPUiaWohWmGg25-C1qBHkzu_-qhZqQd4Eh4iKswM&dib_tag=se&keywords=Enema+butt+plug+nozzle&qid=1753957476&sr=8-2

The ones off Amazon have been hit and miss for me in terms of quality. Some have lasted 6 months, others have lasted years. As others have stated make sure you’re inflating the balloons enough. I generally take 14 puffs of inflation for the inner balloon and 3 for the external. Good luck!

Hi everyone! I have to agree with @selfmadetoy on the latex model that you don’t get a “good” seal without over inflating it even at that I wouldn’t be trying any extra curricular activity with it but the yellow and orange one med tech sells with the single inflator for two balloons is the best at locking my ass down!! Sorry selfmadetoy I was surprised it didn’t do better also

Aside from what has already been mentioned, in my experience I also have to make sure the internal balloon is “seated” in the rectum to get a perfect seal. For me this involves a couple of slow iterations of relaxing and bearing down as I get the balloon in place.

Good luck, and I hope you find what works for you!

I have 'had' both 'flavors' of the inflatable e-nozzles - They were both short lived and leaked. I tried the 'butt plug' style and found it to be uncomfortable and it seemed to take my mind off of the 'Pleasurable' task at hand. Now days I use a bulbous plastic barium style nozzle that I polished a bit and took the flashing off of the water delivery holes. Que Sera, Sera...

My issue with double balloon nozzles was the fact that after a few uses, a tear developed at the smaller flange and the tubing. I tried cement for the purpose of repair. It held once or twice, then failed again. Been some time back. Haven’t had one since.

I very much enjoy having such a nozzle used on me by a caregiver or other person willing to administer an enema and though I don’t have one now, am toying with the idea of purchasing another one.

I was very aroused the last time I had the double balloon used on me, and the arousal as a result of the effort the caregiver was making to get it into and beyond my anus and into my rectum was stimulating and intense for me.

It’s been a while and yes I have received enemas recently (posted about that) but I definitely want this particular person ( female) new to the enema scene) to employ a double balloon nozzle in a future enema session(s).

And if we do a session and she is comfortable with it I will look forward to more; with the hope then nozzle does not tear.

If the catheter is not defective or damaged, is there a possibility you actually used too much lubrication getting the first balloon past your anus? I use a silicon lubricant which is very slippery, you might try using less lubricant. Obviously you would not want to insert it dry, could hurt and cause damage.

Hope this helps - the hoseman

The newer double balloon nozzles have too much space in between in my opinion. I had a double latex model made in Poland that had half the distance between the two that sealed really well. It didn't take as much air to seal, aka the balloons were not being stretched as much. Over time it fell apart and was not able to replace it. The newer silicon nozzles are ok, but I do miss the feeling of the latex. I do have a stray inflatable that was made in reverse, it worked ok. I'm back to the knobbed delrin nozzles. Is there anyone still making these or know of a supply?

"The newer double balloon nozzles have too much space in between in my opinion"

I agree on this for the ones from Med tech. But when I dress up for a enema session, I dress in a pantyhose with a small hole at the rear. With one balloon inside me and the other balloon outside the pantyhose I get a much better pressure and sealant for the inner balloon.